ATV-Ctrl2
Ready assembled modules from commercial production.
Crystal controlled frequency, controlled by a PIC synthesizer, the usual repeater and simplex frequencies are already stored in the PIC (13cm: 4 frequencies, 23cm: 8 frequencies). Frequency is selected by DIP switches. With the possibility to use several channels a full duplex ATV connection becomes possible. With existing amplifiers and receive amplifiers the modules can be extended to a full TV rig. With their small size these modules can be integrated in remote controlled vehicles like cars, boats etc. Cinch connectors for AF and video, SMA connector for antenna, coaxial DC connector.
Frequencies
| 13 cm | 2329 | 2343 | 2380.5 | 2438 | MHz | ||||
| ISM | 2413 | 2483 | 2458 | 2475 | MHz | ||||
| 23 cm | 1251.625 | 1280 | 1278.250 | 1276.5 | 1275 | 1281.25 | 1247 | 1285 | MHz |
| Transmitter: | |
| AF carrier | 5.5 MHz to 7.0 MHz |
| Input level: | Audio + Video 1V |
| DC supply voltage: | 13.8V DC, 200mA |
| Sizes: | 60*125mm, 18mm high |
TX power 20mW (13cm) or 50mW (23cm) to SMA connector, video level can be adjusted with pot on the PCB. Sound carrier (stereo) can be set to any shift from 5.3 to 7MHz (default 6.0/6.5 MHz). The HF module can be placed vertically, reducing the largest size from 125mm to 75mm.
Receiver: |
|
| Display: | 4 LED for channel |
| Sound carrier: | as TX |
| Output level: | Audio + Video 1V |
| DC supply voltage: | 13.8V DC, 500mA |
| Sizes: | 60*150mm, 18mm high |
The output level (video) can be adjusted with a potentiometer, 4 LEDs show selected channel, one push button to start channel scan, stereo sound with 6.0 / 6.5 MHz sub carriers (can be modified to 5.5 MHz). Inverse video signal available on PCB.
For use with our ATV modules, replaces the original PIC controller and enables frequency selection in 125kHz steps with Up/Down buttons. The selected frequencies of the transmitter and the receiver are displayed on the LCD simultaneously (the picture shows the old version with only one line).
You can connect each one transmitter and one receiver at the same time. The frequency can be entered for TX and RX separately, even on different bands enabling crossband operation.
Frequency range:
13cm : 2320 MHz - 2450 MHz
23cm : 1240 MHz - 1300 MHz
The selected frequencies are stored permanently. The connection to the modules is done with a flat ribbon cable connecting to the socket of the original PIC. Just unplug the PIC of teh module and replace it with the connector from the controller. No soldering required, no separate power supply for the controller required.
Size: 58mm x 37mm
Instruction all ATV components (German, PDF, ca. 400 KB) Instructions for ATV-CTRL3 (German, PDF, ca. 80 KB) |
 |
||
| Article | 17010.23SMA | 17010.23SM-5 | |
| Type | Rubber coil | Dipole | |
| Length | 9.5 | 20.5 | cm |
| Connector | SMA | SMA | |
| Price | 10.51 (10.20) EUR | 19.88 (19.30) EUR | |
|
|
|
 |
 |
| For 13cm (2300-2500 MHz), Length ca. 8cm, SMA connector | ||
|
Order No.
17010.10 straight 8.96 ( 8.70) EUR
|
Order No.
17010.11 90° angled 11.12 (10.80) EUR
|
Order No.
17010.12 Dipole with cable, self adhesive 18.54 (18.00) EUR
|
| Diese Seite drucken | Diese Seite zu den Favoriten hinzufügen |